Gestetner DSC545 Magenta Developer Replacement B230-9670, B2309670
Gestetner DSC545 Magenta Developer Replacement – One solution which typically may get missed when working with print quality could be the developer. Old developer might cause to washed out pictures, coloration voids, and numerous other problems. The developer wears out through a drawn out period of time therefore the majority of consumers tend not to realize the drop in print quality till it gets extremely below average.
Since worn out developer usually presents itself just like low toner individuals are likely to change the toner cartridge 1st. Once individuals learn that doesn’t seem to correct the problem they sometimes give a call for assistance. In this article you will find the developer replacement directions to help reestablish the clear dazzling colors you demand when making use of one of these expensive products.
Ricoh B230-9670 Magenta Developer (Genuine) – $61.95
B230-9670, B2309670
Gestetner DSC545 Magenta Developer Replacement
The new drum unit has a front cover and a front joint. When you attach the new drum unit to the development unit, remove a front cover and a front joint at first.
And use them for reassembling the new drum unit and development unit.
Entering SP Mode
1. Press the “Clear Mode” key.
2. Use keypad to enter “107”.
3. Hold down “Clear/Stop” Â for 3 seconds at least.
4. Enter the Service Mode.
If you install a new drum unit, set SP 3902-xxx to “1”.
Black: 3902-009
Yellow: 3902-010
Cyan: 3902-011
Magenta: 3902-012
If you do this, then the machine will reset the PM counter for the drum unit automatically, after you turn the power on again.
Turn the machine power off.
1-2. PCU ( “PCU”)
3. Front cover [A] ( x 2)
4. Do not touch the bearing [B] after removing the front cover. The bearing is properly applied with lubricant.
Note: Remove the toner duct [G] first to avoid breaking it during this procedure.
5. Remove the bushing [C] of the development roller at the rear of the PCU ( x 1).
6. Remove the front joint [D] ( x 1, x 1).
The front joint [D] is firmly set. Remove it with a watchmaker’s or jeweller’s screwdriver.
Drum unit [E] and Development Unit [F] [G]
When the development unit is removed from the drum unit, clean the entrance mylar [G] with a vacuum.
If you change the development unit, do the ACC procedure.
3902 Turns the new unit detection flag for each PM unit on or off.
The use of these counters is explained in the PM section and in the relevant parts of section 3 (Replacement and Adjustment).
Entering SP Mode
1. Press the “Clear Mode” key.
2. Use keypad to enter “107”.
3. Hold down “Clear/Stop” Â for 3 seconds at least.
4. Enter the Service Mode.
If you install a single new developer or developer unit only reset that particular developer or unit, set SP 3902-xxx to “1”.
001 Development Unit: Bk *ENG
002 Development Unit: Y *ENG
003 Development Unit: C *ENG
004 Development Unit: M *ENG
005 Developer: Bk *ENG
006 Developer: Y *ENG
007 Developer: C *ENG
008 Developer: M *ENG
A. Turn the machine power off.
B. Development unit ( “Drum Unit and Development Unit”)
7. Hopper cover [A] (hook x 3)
8. Shake a bag of developer and pour it into the development hopper [B].
9. Reattach the hopper cover (hook x 3)
10. Turn the machine power on. The machine initializes the developer and resets the PM counter for the developer. (For details of the developer initialization result, see “Developer Initialization Result” in the “Troubleshooting” chapter.
8. Do the ACC procedure.
Ricoh B230-9670 Magenta Developer (Genuine) – $61.95 Genuine Ricoh B230-9670 Magenta Developer; Developer – Genuine Ricoh Brand – Replace every 160,000 pages; Mfr PNs: Ricoh B2309670, Savin B230-9670, B2309670, Gestetner B230-9670, B2309670, Lanier B230-9670, B2309670; Color: Magenta |
