Kyocera FS1030MFP, FS1035MFP Error Code List
Below you will find the Kyocera FS1030MFP, FS1035MFP Error Code List along with information that will help you isolate the problem and figure out what is causing the issue and what needs to be done to solve it.
Note :Â Majority of the time the service manual is pretty good and getting you to the point of your problem. However, there are cases where the error might be caused by other issues. Therefore, it’s not 100 percent guaranteed that if you follow the steps below it will fix all your issues. This should be used as a tool to help fix your problem.
0030 FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem.
Defective FAX control PWB.
Replace the FAX control PWB
0070 FAX control PWB incompatible detection Error
Abnormal detection of FAX control PWB incompatibility
In the initial communication with the FAX control PWB, any normal communication command is not transmitted.
Defective fax software.
Defective FAX control PWB.
Install the fax software.
Replace the FAX control PWB
0100 Backup memory device error
Defective flash memory.
Defective control PWB.
Replace the control PWB
Replace the control PWB
0120 MAC address data error
Defective flash memory.
Replace the control PWB
0130 Backup memory read/write error
Defective flash memory.
Defective control PWB.
Replace the control PWB
Replace the control PWB
0140 Backup memory data error
Defective flash memory.
Defective control PWB.
Replace the control PWB
Replace the control PWB
0150 Control PWB EEPROM error
Detecting control PWB EEPROM (U17) communication error.
Improper installation control PWB EEPROM (U17).
Defective control PWB.
Data damage of control PWB EEPROM (U17).
Check the installation of the EEPROM (U17) and remedy if necessary
Replace the control PWB
Contact the Service Administrative Division.
0170 Billing counting error
Defective control PWB.
Data damage of control PWB EEPROM (U17).
Replace the control PWB
Contact the Service Administrative Division.
0180 Machine number mismatch
Machine number of main and engine does not match.
The main PWB or the engine PWB were exchanged.
Data damage of control PWB EEPROM (U17).
U004 Setting the machine number
Contact the Service Administrative Division.
0420 Paper feeder communication error
Communication error between control PWB and optional paper feeder.
Improper installation paper feeder.
Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion.
Defective control PWB.
Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion.
Defective PF main PWB.
Follow installation instruction carefully again.
Reinsert the connector.
Also check for continuity within the connector harness.
If none, remedy or replace the harness.
Replace the control PWB
Reinsert the connector.
Also check for continuity within the connector harness.
If none, remedy or replace the harness (Refer to the service manual for the paper feeder).
Replace the PF main PWB (Refer to the service manual for the paper feeder).
0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB.
Defective fax software.
Defective FAX control PWB.
Install the fax software.
Replace the FAX control PWB
0840 Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or
more have passed.
Defective control PWB.
The battery is disconnected from the control PWB.
Replace the control PWB
Check visually and remedy if necessary.
0870 FAX control PWB to control PWB high capacity data transfer problem
High-capacity data transfer between the FAX control PWB and the control PWB of the machine was not normally
performed even if the data transfer was retried the specified times.
Improper installation FAX control PWB.
Defective FAX control PWB or control PWB.
Reinstall the FAX control PWB
Replace the FAX control PWB or control PWB and check for correct operation.
0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB.
Defective FAX control PWB.
Replace the FAX control PWB
2000 Main motor error
The main motor ready input is not given for 2 s during the main motor is ON.
Defective harness between main motor (CN1) and control PWB (YC17), or improper connector insertion.
Defective drive transmission system of the main motor.
Defective main motor.
Defective control PWB.
Reinsert the connector.
Also check for continuity within the connector harness.
If none, remedy or replace the harness
Check if the rollers and gears rotate smoothly.
If not, grease the bushings and gears.
Check for broken gears and replace if any.
Replace the main motor
Replace the control PWB
2610 PF paper feed motor error (paper feeder)
The PF paper feed motor of cassette 2 ready input is not given for 2 s during the PF paper feed motor is ON.
Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion.
Defective PF paper feed motor drive transmission system.
Defective PF main motor.
Defective control PWB.
Reinsert the connector.
Also check for continuity within the connector harness.
If none, remedy or replace the harness (Refer to the service manual for the paper feeder).
Check if the gears rotate smoothly.
If not, grease the bushings and gears.
Check for broken gears and replace if any.
Replace the PF main motor.
Replace the control PWB
2620 PF paper feed motor error (Paper feeder)
The PF paper feed motor of cassette 3 ready input is not given for 2 s during the PF paper feed motor is ON.
Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion.
Defective PF paper feed motor drive transmission system.
Defective PF main motor.
Defective control PWB.
Reinsert the connector.
Also check for continuity within the connector harness.
If none, remedy or replace the harness (Refer to the service manual for the paper feeder).
Check if the gears rotate smoothly.
If not, grease the bushings and gears.
Check for broken gears and replace if any.
Replace the PF main motor (Refer to the service manual for the paper feeder).
Replace the control PWB
3100 ISU home position error
Defective FFC between CCD PWB (YC1) and control PWB (YC8).
Defective FFC between control PWB (YC6) and scanner PWB (YC103), or improper FFC insertion.
Defective home position sensor.
Defective harness between ISU motor and scanner PWB (YC104), or improper connector insertion.
Defective ISU motor.
Replace the image scanner unit (ISU)
Reinsert the FFC.
Also check for continuity within the FFC.
If none, remedy or replace the FFC.
Replace the home position sensor.
Reinsert the connector.
Also check for continuity within the connector harness.
If none, remedy or replace the harness.
Replace the ISU motor.
3200 Exposure lamp error
The exposure lamp is not turned on.
Defective FFC between scanner PWB (YC103) and control PWB (YC6), or improper FFC insertion.
Defective FFC between CCD PWB (YC1) and control PWB (YC8).
Defective harness between CCD PWB (YC3) and LED drive PWB (YC1), or improper connector insertion.
Defective harness between LED drive PWB (YC2) and exposure lamp, or improper connector insertion.
Defective exposure lamp.
Defective LED drive PWB.
Defective control PWB.
Reinsert the FFC. Also check for continuity within the FFC. If none, remedy or replace the FFC.
Replace the image scanner unit (ISU)
Reinsert the connector. Also check for
continuity within the connector harness.
If none, remedy or replace the harness.
Reinsert the connector.
Also check for continuity within the connector harness.
If none, remedy or replace the harness.
Replace the exposure lamp
Replace the LED drive PWB
Replace the control PWB
3300 AGC error
After AGC, correct input is not obtained at CCD.
Defective FFC between CCD PWB (YC1) and control PWB (YC8).
Defective exposure lamp.
Defective CCD PWB.
Defective control PWB.
Replace the image scanner unit (ISU)
Replace the exposure lamp
Replace the CCD PWB.
Replace the control PWB
3300 AGC error
After AGC, correct input is not obtained at CCD
Defective FFC between CCD PWB (YC1) and control PWB (YC8).
Defective CCD PWB.
Defective control PWB.
Replace the image scanner unit (ISU)
Replace the CCD PWB.
Replace the control PWB
4000 Polygon motor (laser scanner unit) error
The polygon motor ready input is not given for 6 s during the polygon motor is ON.
Defective harness between polygon motor and control PWB (YC10), or improper connector insertion.
Defective laser scanner unit.
Defective control PWB.
Reinsert the connector.
Also check for continuity within the connector harness.
If none, remedy or replace the harness.
Replace the laser scanner unit
Replace the control PWB
4200 BD error (laser scanner unit) error BD sensor does not detect laser beam due to condensation on the polygon mirror.
Defective laser scanner unit.
Defective control PWB.
Turn machine power off for at least 30 minutes, then turn machine on again.
If not cured, replace the laser scanner unit
Replace the laser scanner unit
Replace the control PWB
6000 Broken Fuser heater wire
The fuser temperature does not rise after the Fuser heater has been turned on.
Poor contact in the fuser thermistor connector terminals.
Poor contact in the Fuser heater connector terminals.
Fuser thermistor installed incorrectly.
Fuser thermal cutout triggered.
Fuser heater installed incorrectly.
Broken Fuser heater wire.
Reinsert the connector
Replace the fuser unit
6020 Abnormally high fuser thermistor temperature
Fuser thermistor detects abnormally temperature.
Shorted fuser thermistor.
Defective control PWB.
Replace the control PWB
6030 Broken fuser thermistor wire
Input from fuser thermistor is 0 (A/D value).
Poor contact in the fuser thermistor connector terminals.
Broken fuser thermistor wire.
Fuser thermistor installed incorrectly.
Fuser thermal cutout triggered.
Fuser heater installed incorrectly.
Broken Fuser heater wire.
Reinsert the connector.
Replace the fuser unit
6400 Zero cross signal error
The zero cross signal does not reach the control PWB for specified time.
Defective harness between high voltage PWB (YC202) and control PWB (YC23), or improper connector insertion.
Defective connection between power source PWB (YC103) and high voltage PWB (YC201).
Defective power source PWB.
Defective control PWB.
Reinsert the connectors.
Also check for continuity within the connector harness.
If none, remedy or replace the harness (See page 1-5-37).
Replace the power source PWB
Replace the control PWB
7990 Waste toner full
The waste toner sensor has detected that the waste toner reservoir (drum unit) is full.
Waste toner reservoir (drum unit) is full.
Defective waste toner sensor.
Defective control PWB.
Turn the power switch off/on to restart the machine.
If the error is not resolved, replace the drum unit
Replace the waste toner sensor.
Replace the control PWB
F000 Control PWB – Operation panel
PWB communication error
Defective harness between operation panel PWB (YC1) and control PWB (YC7), or improper connector insertion.
Defective operation panel PWB.
Defective control PWB.
Reinsert the connector.
Also check for continuity within the connector harness.
If none, remedy or replace the harness.
Replace the operation panel PWB.
Replace the control PWB
F020 Control PWB RAM checksum error
Defective main memory (RAM) on the control PWB.
Defective expanded memory (DIMM).
Turn the power switch off/on to restart the machine.
If the error is not resolved, replace control PWB.
Replace the expanded memory (DIMM).
F040 Control PWB engine communication error
A communication error is detected.
Defective control PWB.
Turn the power switch off/on to restart the machine.
If the error is not resolved, replace control PWB.
F041 Control PWB – scanner PWB communication error
A communication error is detected.
Defective control PWB or scanner PWB.
Turn the power switch off/on to restart the machine.
If the error is not resolved, replace control PWB or scanner PWB
F050 Control PWB engine checksum error
Some error may have occurred when downloading the firmware of the control PWB.
Defective control PWB.
Download the firmware of the control PWB again
Turn the power switch off/on to restart the machine.
If the error is not resolved, replace control PWB
F186 Control PWB video data control error
Defective control PWB.
Turn the power switch off/on to restart the machine.
If the error is not resolved, replace control PWB
