Canon D1120, D1150, D1170, D1180 Error Code List
Below you will find the Canon D1120, D1150, D1170, D1180 Error Code List. Find the error code that your machine is displaying and find out whats going on and where to look for possible solutions.
E000 0 Startup error
The temperature detected by the main or sub thermistor does not rise to the
specified value during startup control.
– Check the fixing film connector.
– Replace the fixing film unit.
– Replace the Engine controller PCB.
E001 0 Abnormally high temperature (detected by main thermistor)
The main thermistor detected an abnormally high temperature during
temperature control.
– Check the connector of the fixing film unit.
– Replace the fixing film unit.
– Replace the Engine controller PCB.
E001 1 Abnormally high temperature (detected by sub thermistor)
The sub thermistor detected an abnormally high temperature during
temperature control.
– Check the connector of the fixing film unit.
– Replace the fixing film unit.
– Replace the Engine controller PCB.
E002 0 Low temperature during temperature control.
The target temperature is not reached
during temperature control.
– Check the connector of the fixing film unit.
– Replace the fixing film unit.
– Replace the Engine controller PCB.
E003 0 Abnormally low temperature (detected by main thermistor)
After the temperature detected by the main thermistor has reached the specified value, it does not reach the
specified value during initial rotation.
– Check the connector of the fixing film unit.
– Replace the fixing film unit.
– Replace the Engine controller PCB.
E003 1 Abnormally low temperature (detected by sub thermistor)
After the temperature detected by the sub thermistor has reached the specified value, it does not reach the specified value during initial rotation.
– Check the connector of the fixing film unit.
– Replace the fixing film unit.
– Replace the Engine controller PCB.
E010 0 Main motor failure
The main motor is faulty. – Check the connector of the main motor.
– Replace the main motor.
– Replace the Engine controller PCB.
E100 0 BD detection PCB failure
The BD detection PCB is faulty. – Replace the laser scanner unit.
– Replace the Engine controller PCB.
E196 1 Flash ROM write/read error – Replace the Main Controller Board.
The write/read of Flash ROM in the Main Controller Board is faulty.
E196 2 PCL ROM write/read error – Replace the Main Controller Board.
The write/read of PCL ROM in the Main Controller Board is faulty.
E197 0 Printer engine communication error
Erroneous communication between the Engine controller PCB and Main Controller Board was detected.
– Check the connectors of the Engine controller PCB and Main Controller Board.
– Replace the Engine controller PCBÂ for normal connection.
– Replace the Main Controller Board.
E716 0 Erroneous communication with optional cassette
Disconnection of the optional cassette was detected after power-on, detection of normal connection to the optional cassette, and start of communication.
– Check the connectors of the optional cassette PCB and Engine controller PCB.
– Replace the optional cassette PCBÂ for normal connection.
– Replace the Engine controller PCB.
E730 0 inside error of the Main Controller Board (PDL system error)
– Replace the Main Controller Board.
The inside of the Main Controller Board is faulty.
E733 0 Erroneous communication between controller and printer
Cannot communicate with the printer at startup.
– Check the connectors of the Engine controller PCB and Main Controller Board for normal connection.
– Check the power supply of the printer (Check whether initialization is performed at startup).
– Replace the Engine controller PCBÂ or Main Controller Board.
E736 0 CCU communication error
The installed modem PCB is incompatible.
– Check the connectors of the Main Controller Board and modem.
– Replace the modem PCB.
– Replace the Main Controller Board.
E739 0 Erroneous communication between controller and network board
The installed network board is incompatible.
– Replace the Main Controller Board.
E805 0 Fan failure
The fan is faulty. – Check the fan connector.
– Replace the fan.
– Replace the Engine controller PCB.
E808 0 Fixing drive circuit failure
– The heater does not turn on.
– A fixing drive motor failure was detected.
– Check the connector of the fixing film unit.
– Replace the fixing film unit.
– Replace the fixing drive motor.
– Replace the Engine controller PCB.
– Replace the power supply PCB
