Lanier LD117SPF B0444170 Upper Fuser Roller Gear Replacement Procedure

 

Lanier LD117SPF B0444170 Upper Fuser Roller Gear Replacement Instructions

Below you will find the illustrated Lanier LD117SPF B0444170 Upper Fuser Roller Gear Replacement instructions. Below you will find a link to order in a replacement hot roller gear and the illustrated instructions on how to replace it in your machine..

Fusers heat up to around 375 decrees. Therefore the hot roller gear dries out and gets extremely brittle. Eventually they will either crack and either stop turning the hot roller or fall apart and make a horrible grinding noise in the fuser. Either way it will cause the machine to jam just before the fuser as the hot roller is no longer turning. If you find yourself in this situation then you need to get a gear on order.

Lanier LD117SPF B0444170 Upper Fuser Roller Gear
Part Numbers
Ricoh B044-4170, B0444170
Savin B044-4170, B0444170
Gestetner B044-4170, B0444170
Lanier B044-4170, B0444170
Nashuatec B0444170

1. Lanier LD117SPF FUSING UNIT
CAUTION : Before handling the fusing unit, make sure that the unit is cool enough. The fusing unit can be very hot.
1. Copy tray

2. Open the right door.
3. Connector cover [A] (! x 1)
NOTE: When reinstalling, attach the ground wire.
4. Fusing unit [B] (! x 2, ” x 4)

2. Lanier LD117SPF EXIT SENSOR
1. Fusing unit
2. Exit sensor [A] (” × 1)

3-4. Lanier LD117SPF HOT ROLLER STRIPPER PAWLS
CAUTION: Do not damage the hot roller stripper pawls and the tension springs.
1. Fusing unit
2. Separate the fusing unit into two sections: the hot roller section [A] and the pressure roller section [B]
NOTE: After removing the screws, lower the pressure roller section about halfway and then slide it toward the front side to detach it.
3. Support rollers [C]
4. Hot roller stripper pawls [D]
NOTE: Remove the spacer [E] if you are removing the hot roller assembly

5-6. Lanier LD117SPF HOT ROLLER & FUSING LAMP
CAUTION: Do not touch the fusing lamp and rollers with your bare hands.
1. Hot roller stripper pawls and spacers
2. Hot roller assembly [A] (! x 2)
3. Fusing lamp [B]
NOTE: When reassembling, check that the direction of the fusing lamp is correct [C][D].
4. Hot roller [C] (2 C-rings, 1 spacer, 1 gear, 2 bushings, 1 cover [D])
Reassembling Use caution:
• The fusing lamp is positioned correctly.
• The fusing lamp does not touch the internal part of the hot roller.

Lanier LD117SPF B0444170 Upper Fuser Roller Gear Replacement Instructions – Illustrated

Lanier LD117SPF B0444170 Upper Fuser Roller Gear Replacement
Now, if you are up to it and decide it might be in your best interest to just rebuild the whole unit then click on the link below and get the fuser 90K PM Kit. You’ve will already have done most the work anyway and buying the kit will save you money over buying and replacing the parts piece by piece. However, the gear is not included in the kit so if you buy the kit you will need to order the gear also.


Replacement Fuser Roller RICOH MP161 MP171 MP201 Lanier LD117 LD220

Piec FUSER UNIT Ricoh Aficio MP171 MP171F MP171SPF MP201SPF wymiana wałków, separatorów, lamp, łożysk, odrywaczy Ricoh Aficio MP171 Ricoh Aficio MP171F Ricoh Aficio MP171SPF...

We will be happy to hear your thoughts

Leave a reply

Shopping cart