Lanier LD445C Yellow Developer Replacement B230-9680, B2309680

 

Lanier LD445C Yellow Developer Replacement B230-9680, B2309680

Lanier LD445C Yellow Developer Replacement – One component which usually can become ignored while working with print quality could be the developer. Worn developer may cause to washed out printing, full color voids, and other troubles. The developer wears out over a long span of time and thus many consumers usually do not recognize the reduction in print quality till it gets really awful.

Considering the fact that used developer often appears similar to low toner customers have the inclination to switch out the toner cartridge before anything else. When people learn that isn’t going to fix the condition they usually give a call for service. Below you will find the developer repair assistance to help get back the sharp radiant colors you expect when working with one of these pricey products.


B230-9680, B2309680

Lanier LD445C Yellow Developer Replacement

The new drum unit has a front cover and a front joint. When you attach the new drum unit to the development unit, remove a front cover and a front joint at first.
And use them for reassembling the new drum unit and development unit.

Entering SP Mode
1. Press the “Clear Mode” key.
2. Use keypad to enter “107”.
3. Hold down “Clear/Stop”  for 3 seconds at least.
4. Enter the Service Mode.
If you install a new drum unit, set SP 3902-xxx to “1”.
Black: 3902-009
Yellow: 3902-010
Cyan: 3902-011
Magenta: 3902-012
If you do this, then the machine will reset the PM counter for the drum unit automatically, after you turn the power on again.
Turn the machine power off.

1-2. PCU ( “PCU”)
3. Front cover [A] ( x 2)
4. Do not touch the bearing [B] after removing the front cover. The bearing is properly applied with lubricant.
Note: Remove the toner duct [G] first to avoid breaking it during this procedure.
5. Remove the bushing [C] of the development roller at the rear of the PCU ( x 1).
6. Remove the front joint [D] ( x 1, x 1).
The front joint [D] is firmly set. Remove it with a watchmaker’s or jeweller’s screwdriver.
Drum unit [E] and Development Unit [F] [G]

Lanier LD445C Yellow Developer Replacement

When the development unit is removed from the drum unit, clean the entrance mylar [G] with a vacuum.
If you change the development unit, do the ACC procedure.

3902 Turns the new unit detection flag for each PM unit on or off.
The use of these counters is explained in the PM section and in the relevant parts of section 3 (Replacement and Adjustment).

Entering SP Mode
1. Press the “Clear Mode” key.
2. Use keypad to enter “107”.
3. Hold down “Clear/Stop”  for 3 seconds at least.
4. Enter the Service Mode.

If you install a single new developer or developer unit only reset that particular developer or unit, set SP 3902-xxx to “1”.
001 Development Unit: Bk *ENG
002 Development Unit: Y *ENG
003 Development Unit: C *ENG
004 Development Unit: M *ENG
005 Developer: Bk *ENG
006 Developer: Y *ENG
007 Developer: C *ENG
008 Developer: M *ENG
A. Turn the machine power off.
B. Development unit ( “Drum Unit and Development Unit”)
7. Hopper cover [A] (hook x 3)
8. Shake a bag of developer and pour it into the development hopper [B].
9. Reattach the hopper cover (hook x 3)
10. Turn the machine power on. The machine initializes the developer and resets the PM counter for the developer. (For details of the developer initialization result, see “Developer Initialization Result” in the “Troubleshooting” chapter.
8. Do the ACC procedure.

B2309680 Yellow Developer B230-9680

$39.99  in stock
Item condition: New
Ended: Aug 7, 11:04PST
eBay
as of April 15, 2024 4:52 pm

Ricoh MPC color copier - Changing Developer

For MPC 2000,2500,2800,3000,3300,3500,4000,4500,5000.

We will be happy to hear your thoughts

Leave a reply

Shopping cart