Lanier LD445C Black Developer Replacement B230-9640, B2309640

 

Lanier LD445C Black Developer Replacement B230-9640, B2309640

Lanier LD445C Black Developer Replacement – One item which sometimes can become missed while dealing with print quality can be the developer. Used developer is likely to cause to washed out print, coloration voids, and various other situations. The developer wears out throughout a drawn out interval of time which means that the majority of people don’t observe the decline in print quality until it gets unquestionably undesirable.

Seeing that worn out developer frequently appears much like low toner employees often tend to replace the toner cartridge before anything else. Once people find that isn’t going to correct the problem they typically call for service. Beneath you will find the developer replacing information to help reestablish the distinct dazzling colors you expect while using one of these pricey products.


B230-9640, B2309640

Lanier LD445C Black Developer Replacement

The new drum unit has a front cover and a front joint. When you attach the new drum unit to the development unit, remove a front cover and a front joint at first.
And use them for reassembling the new drum unit and development unit.

Entering SP Mode
1. Press the “Clear Mode” key.
2. Use keypad to enter “107”.
3. Hold down “Clear/Stop”  for 3 seconds at least.
4. Enter the Service Mode.
If you install a new drum unit, set SP 3902-xxx to “1”.
Black: 3902-009
Yellow: 3902-010
Cyan: 3902-011
Magenta: 3902-012
If you do this, then the machine will reset the PM counter for the drum unit automatically, after you turn the power on again.
Turn the machine power off.

1-2. PCU ( “PCU”)
3. Front cover [A] ( x 2)
4. Do not touch the bearing [B] after removing the front cover. The bearing is properly applied with lubricant.
Note: Remove the toner duct [G] first to avoid breaking it during this procedure.
5. Remove the bushing [C] of the development roller at the rear of the PCU ( x 1).
6. Remove the front joint [D] ( x 1, x 1).
The front joint [D] is firmly set. Remove it with a watchmaker’s or jeweller’s screwdriver.
Drum unit [E] and Development Unit [F] [G]

Lanier LD445C Black Developer Replacement

When the development unit is removed from the drum unit, clean the entrance mylar [G] with a vacuum.
If you change the development unit, do the ACC procedure.

3902 Turns the new unit detection flag for each PM unit on or off.
The use of these counters is explained in the PM section and in the relevant parts of section 3 (Replacement and Adjustment).

Entering SP Mode
1. Press the “Clear Mode” key.
2. Use keypad to enter “107”.
3. Hold down “Clear/Stop”  for 3 seconds at least.
4. Enter the Service Mode.

If you install a single new developer or developer unit only reset that particular developer or unit, set SP 3902-xxx to “1”.
001 Development Unit: Bk *ENG
002 Development Unit: Y *ENG
003 Development Unit: C *ENG
004 Development Unit: M *ENG
005 Developer: Bk *ENG
006 Developer: Y *ENG
007 Developer: C *ENG
008 Developer: M *ENG
A. Turn the machine power off.
B. Development unit ( “Drum Unit and Development Unit”)
7. Hopper cover [A] (hook x 3)
8. Shake a bag of developer and pour it into the development hopper [B].
9. Reattach the hopper cover (hook x 3)
10. Turn the machine power on. The machine initializes the developer and resets the PM counter for the developer. (For details of the developer initialization result, see “Developer Initialization Result” in the “Troubleshooting” chapter.
8. Do the ACC procedure.

B2309640 Black Developer Aficio MP C2000 Aficio MP C2000SPF B230-9640

$39.99  in stock
Item condition: New
Ended: Apr 4, 06:12PST
eBay
as of January 8, 2024 3:00 am

Ricoh MPC color copier - Changing Developer

For MPC 2000,2500,2800,3000,3300,3500,4000,4500,5000.

We will be happy to hear your thoughts

Leave a reply

Shopping cart