Lanier LD016 PMB12990K Replacement Procedure

 

Lanier LD016 PMB12990K Replacment Instructions

Below you will find the illustrated Lanier LD016 PMB12990K Replacement instuctions. Yeah, I know, these machines are getting on in age. Excuse me, I just happened to look up the instructions, saw they were pretty straight forward, and found out you can still get the parts. So, I figured what the heck.

While these machines are old, they have a bottled toner. Why is that important? Just ask your customer how much they are paying for those toners. Yeah, they are dirt cheap, therefore these machines are surprising economical to run so some customers like to keep them around as long as possible.

Lanier LD016 Maintenance Kit – 90K – Genuine Ricoh Kit
Kit Includes:
(1) Hot Roller [AE01-1086]
(1) Pressure Roller [AE02-0107]
(2) Fusing Bushing [AE03-1034]
(3) Stripper Pawl [AE04-4059]
(1) Transfer Roller [B044-3802]
(1) Separation Plate [B044-3857]

1. Lanier LD016 FUSING UNIT
CAUTION : Before handling the fusing unit, make sure that the unit is cool enough. The fusing unit can be very hot.
1. Copy tray
2. Open the right door.
3. Connector cover [A] (! x 1)
NOTE: When reinstalling, attach the ground wire.
4. Fusing unit [B] (! x 2, ” x 4)

2. Lanier LD016 EXIT SENSOR
1. Fusing unit
2. Exit sensor [A] (” × 1)

3-4. Lanier LD016 HOT ROLLER STRIPPER PAWLS
CAUTION: Do not damage the hot roller stripper pawls and the tension springs.
1. Fusing unit
2. Separate the fusing unit into two sections: the hot roller section [A] and the pressure roller section [B]
NOTE: After removing the screws, lower the pressure roller section about halfway and then slide it toward the front side to detach it.
3. Support rollers [C]
4. Hot roller stripper pawls [D]
NOTE: Remove the spacer [E] if you are removing the hot roller assembly

5-6. Lanier LD016 HOT ROLLER & FUSING LAMP
CAUTION: Do not touch the fusing lamp and rollers with your bare hands.
1. Hot roller stripper pawls and spacers
2. Hot roller assembly [A] (! x 2)
3. Fusing lamp [B]
NOTE: When reassembling, check that the direction of the fusing lamp is correct [C][D].
4. Hot roller [C] (2 C-rings, 1 spacer, 1 gear, 2 bushings, 1 cover [D])
Reassembling Use caution:
• The fusing lamp is positioned correctly.
• The fusing lamp does not touch the internal part of the hot roller.

7. Lanier LD016 THERMO-SWITCH AND THERMISTOR
1. Hot roller assembly
2. Thermo-switches [A][B] (! x 2 for each)
3. Thermistor [C] (! x 1)
Reassembling : Make sure the following:
• The thermistor is in contact with the hot roller.
• The hot roller turns smoothly.

8-9. Lanier LD016 PRESSURE ROLLER
1. Separate the fusing unit into two sections
2. Fusing entrance guide [A]
3. 2 springs [B][C]
4. 2 pressure arms [D][E]
5. Bushing [F]
6. Pressure roller [G]

PMB12990K Replacement Instructions – Illustrated

Lanier LD016 PMB12990K Replacement

Genuine PMB12990K Maintenance Kit – 90K for Lanier LD015; Maintenance Kit – Genuine Ricoh Kit Kit Includes: (1) Hot Roller [AE01-1086] (1) Pressure Roller [AE02-0107] (2) Fusing Bushing [AE03-1034] (3) Stripper Pawl [AE04-4059] (1) Transfer Roller [B044-3802] (1) Separation Plate [B044-3857] Made in USA

Fuser Ricoh AF MP161 MP171 MP201 1515 1013 WYMIANA

Replacement Fuser Roller RICOH MP161 MP171 MP201 Lanier LD117 LD220

Piec FUSER UNIT Ricoh Aficio MP171 MP171F MP171SPF MP201SPF wymiana wałków, separatorów, lamp, łożysk, odrywaczy Ricoh Aficio MP171 Ricoh Aficio MP171F Ricoh Aficio MP171SPF...




We will be happy to hear your thoughts

Leave a reply

Shopping cart